- Academic DIY Kits
- Academic Hobby Projects
- Academic Major Projects
- Academic Minor Projects
- Aeromodelling & Drone
- Development Boards
- Electronics- Active Parts
- Electronics- Passive Parts
- Electronics- Sensors
- Electronics– Accessories
- Mechanical Parts
- Motor, Actuator & Pump
- Robot Accessories
- Supply- Battery, Adopters
- Tools & Equipment
Top rated products
The NRF24L01 module is the latest in RF modules. This module uses the 2.4GHz transceiver from Nordic Semiconductor, the NRF24L01+. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401A and add some extra pipelines, buffers, and an auto-retransmit feature – very nice!
This board features a reverse polarized SMA connector for maximum RF range. And there are PA and LNA circuit on board, with the external antenna it can reach long distance than the one without these parts.
This module comes with the 2.4G antenna (2DB), with 250Kbps transmission rate on open air it can reach the 800-1K meters communication distance.
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Emission mode current(peak): 115mA.
- Receive Mode Current(peak): 45mA.
- Power-down mode current: 4.2uA.
- Sensitivity 2Mbps mode in received: -92dBm.
- Sensitivity 1Mbps mode in received: -95dBm.
- PA gain: 20DbLNA gain: 10Db.
- Sensitivity 250kbps mode in received: -104dBm.
- LNA Noise figure: 2.6Db.
- Antenna Gain (peak): 2Dbi.
- 2MB rate (Open area): 520m.
- 1MB rate (Open area): 750m.
- 250Kb rate (Open area): 1100m.
- Interface: SPI.
- 1 Piece- 2.4GHz NRF24L01 Transreceiver module.
- 1 Piece- SMA Antenna.
MPU-9250 – 9-Axis Gyro Accelerometer Module
₹830.00Add to cart
The MPU-9250 is a 9-axis Motion Tracking device that combines a 3-axis gyroscope, 3-axis accelerometer, 3-axis magnetometer and a Digital Motion Processor™ (DMP) all in a small 3x3x1mm package available as a pin-compatible upgrade from the MPU-6515. With its dedicated I2C sensor bus, the MPU-9250 directly provides complete 9-axis MotionFusion™ output. The MPU-9250 MotionTracking device, …
2 Channel 5V Relay Module
₹180.00Add to cart
This is a 5V, Single Channel Relay interface board; it’s useful to control various appliances, and other equipment’s with large current. It can be controlled directly by any Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, ARM, DSP, MSP430). Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port, or …
LDR Sensor Module Lm393 Optical Photosensitive
₹120.00Add to cart
LDR sensor module is used to detect the intensity of light. It is associated with both analog output pin and digital output pin labeled as AO and DO respectively on the board. When there is light, the resistance of LDR will become low according to the intensity of light. The greater the intensity of light, …
Color Sensor Module TCS230, 3V-5V Red
₹389.00Add to cart
This breakout board is a color sensor based on TAOS TCS230 programmable color light to frequency converter which combines configurable silicon photodiodes and a current –to-frequency convertor on single monolithic CMOS integrated circuit. The light-to-frequency converter reads 8X8 array of photodiodes, each array could filter red, green, blue light or clear from the light source …