Category
- Academic DIY Kits
- Academic Hobby Projects
- Academic Major Projects
- Academic Minor Projects
- Aeromodelling & Drone
- Development Boards
- Electronics- Active Parts
- Electronics- Passive Parts
- Electronics- Sensors
- Electronics– Accessories
- Electronics–Modules
- Mechanical Parts
- Motor, Actuator & Pump
- Robot Accessories
- Supply- Battery, Adopters
- Tools & Equipment
Top rated products
-
Arduino Mega 2560 Micro controller Board (Without Cable)
₹950.00₹825.00 -
Tsop Proximity Sensor Module
₹180.00₹150.00 -
DC Geared Motor-200 RPM Center Shaft
₹160.00₹140.00 -
TSOP1838 IR Receiver Metal
₹30.00₹25.00 -
Hydraulics JCB Using Syringe ₹5,000.00
A4988 is a complete micro-stepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to easy implementation. As long as the “step” input inputting one pulse drives the motor one micro-step. There are no phase sequence tables, high-frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened.
In the micro-step operation, A4988 chopping control inside automatically selects the current decay mode (Slow or Mixed). In mixed decay mode, the device is initially set to a fixed downtime in some fast decay, then the rest of the slow decay downtime. Mixed decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry is provided to improve the pulse-width modulation (PWM) operation power consumption. Internal circuit protection includes thermal shutdown with hysteresis, under-voltage lockout (UVLO), and crossover-current protection. Special power sequencing.
A4988 surface mount QFN package (ES), a size of 5 mm × 5 mm, nominal overall package height of 0.90 mm, with an exposed pad for enhanced thermal dissipation. This package is Pb (suffix-T), with 100% matte tin lead frame plating.
Technical Specifications:
- Simple step and direction control interface
- Short-to-ground and shorted-load protection
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above
- your stepper motor’s rated voltage to achieve higher step rates.
Package Includes:
- 1 Piece- A4988 Stepper Motor Driver Module
- 1 Piece – Heatsink
Weight | 25 g |
---|---|
Dimensions | 20 × 18 × 12 mm |
Related products
-
Dual Motor Driver L293D Module With 7505
₹120.00₹100.00Add to cartDual Motor Driver L293D Module With 7505-contains two inbuilt H-bridge driver circuits and direct IR module input . In its common mode of operation, two DC motors can be driven simultaneously, both in forward and reverse direction. The motor operations of two motors can be controlled by input logic at pins 2 & 7 and …
-
L9110S H Bridge Stepper Motor Dual DC Driver
₹140.00₹125.00Add to cartThe HG7881 (L9110) is a compact motor driver board that supports a voltage range from 2.5-12V at 800mA of continuous current. These chips have built-in output clamp diodes to protect your sensitive microcontroller electronics. They are suitable for small robot projects. Each L9110 chip is able to drive a single DC motor using two digital …
-
DPDT Switch Board Toggle Type
₹120.00₹90.00Add to cartThis is a toggle type DPDT switch Board. It is used in robot control like as forward, backward and Turing movement. its handling is very easy. Technical Specifications: Output Voltage: 12 volt Input Voltage: 12 volt Current Up to: 2Amp Package Includes: 1 Piece- DPDT Switch Board Toggle Type
-
L293D Multi Motor Driver Shield For Arduino SLAEX039
₹240.00₹225.00Add to cartUse this shield to build Robotics and Mechatronics projects based on the Arduino Board. This shield can control all types of popularly used motors – DC Motors, Stepper Motors (both Unipolar and Bipolar Stepper Motors), and Servo Motors! It stacks on top of an Arduino board and requires no external connections using wires or soldering. …
L293D Multi Motor Driver Shield For Arduino SLAEX039Read More
Reviews
There are no reviews yet.