Category
- Academic DIY Kits
- Academic Hobby Projects
- Academic Major Projects
- Academic Minor Projects
- Aeromodelling & Drone
- Development Boards
- Electronics- Active Parts
- Electronics- Passive Parts
- Electronics- Sensors
- Electronics– Accessories
- Electronics–Modules
- Mechanical Parts
- Motor, Actuator & Pump
- Robot Accessories
- Supply- Battery, Adopters
- Tools & Equipment
Top rated products
-
Arduino Uno R3 SMD Board (Without Cable)
₹385.00₹350.00 -
PIR Motion Detector Sensor Module (Hc-Sr501 Pyroelectric Infrared)
₹120.00₹110.00 -
DC Geared Motor-60 RPM Center Shaft
₹160.00₹140.00 -
TSOP1738 38kHz IR Distance Sensor Receiver
₹45.00₹40.00 -
Cyclone Separator For Separate Heavy particles ₹7,500.00
The DRV8825 Stepper Motor Driver with Aluminum Heat Sink is a breakout board for TI’s DRV8825 micro-stepping bipolar stepper motor driver.
The module has a pinout and interface that are nearly identical to those of the A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications.
The DRV8825 features adjustable current limiting, overcurrent, and overtemperature protection, and six micro-step resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
Note: We are supplying two DRV8825 Drivers as DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Good Quality and DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Normal Quality. The difference between them is, the good quality DRV8825 has more PCB layers and it features the connecting pins which are of gold plated as compared to others.
Using the Driver
Technical Specifications:
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45 V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3 V and 5 V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
Package Includes:
- 1 Piece- DRV8825 Stepper Motor Driver
- 1 Piece – Hea sink
Weight | 25 g |
---|
Related products
-
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
₹350.00₹325.00Add to cartVNH2SP30 is a full bridge motor driver intended for a wide range of automotive applications. The device incorporates a monolithic high side driver and two low side switches. The high side driver switch is designed using the ST Microelectronics well-known and proven proprietary VI Power M0 technology which permits efficient integration on the same die …
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)Read More
-
Digital Multi Servo Tester ESC CCPM Consistency Master Speed Control-3 Channel
₹240.00₹210.00Add to cartDIGITAL MULTI SERVO TESTER ESC RC CONSISTENCY CCPM MASTER SPEED CONTROL can connect 1-3 servos simultaneously and test such as 1-3 servos consistency and so on. You can also connect 1-3 ESC to test and compare their reaction time respectively. It can connect 3 servos of the CCPM helicopters and select servos. It can also …
Digital Multi Servo Tester ESC CCPM Consistency Master Speed Control-3 ChannelRead More
-
ULN2003 Stepper Motor Driver Module
₹150.00₹90.00Add to cartThis is ULN2003 Driver Module Stepper Motor Driver, small size, and easy to use. It uses the ULN2003 driver chip to amplify the control signal from the Arduino. This Ultra Lightweight and cheap option commonly used to run and control the small applications stepper motors. Note: Color of PCB may vary according to Manufacturer Technical Specifications: …
-
Dual Monster Moto Shield VNH2SP30 DC Motor Driver 2x14A (Peak 30A)
₹750.00₹680.00Add to cartVNH2SP30 is a full bridge motor driver intended for a wide range of automotive applications. The device incorporates a dual monolithic high side driver and two low side switches. The high side driver switch is designed using the ST Microelectronics well-known and proven proprietary VI Power M0 technology which permits efficient integration on the same …
Dual Monster Moto Shield VNH2SP30 DC Motor Driver 2x14A (Peak 30A)Read More
Reviews
There are no reviews yet.