Category
- Academic DIY Kits
- Academic Hobby Projects
- Academic Major Projects
- Academic Minor Projects
- Aeromodelling & Drone
- Development Boards
- Electronics- Active Parts
- Electronics- Passive Parts
- Electronics- Sensors
- Electronics– Accessories
- Electronics–Modules
- Mechanical Parts
- Motor, Actuator & Pump
- Robot Accessories
- Supply- Battery, Adopters
- Tools & Equipment
Top rated products
-
ADXL345 - Triple Axis Linear Accelerometer
₹125.00₹120.00 -
DHT11 Temperature and Humidity Sensor Module
₹139.00₹135.00 -
DC Geared Motor-500 RPM Center Shaft
₹160.00₹140.00 -
Buzzer-5V 12 MM
₹18.00₹15.00 -
Eight Leg Machine Using Theo Jansen Mechanism ₹8,500.00
Dual Motor Driver L293D Module With 7505-contains two inbuilt H-bridge driver circuits and direct IR module input . In its common mode of operation, two DC motors can be driven simultaneously, both in forward and reverse direction. The motor operations of two motors can be controlled by input logic at pins 2 & 7 and 10 & 15. Input logic 00 or 11 will stop the corresponding motor. Logic 01 and 10 will rotate it in clockwise and anticlockwise directions, respectively.
Enable pins 1 and 9 (corresponding to the two motors) must be high for motors to start operating. When an enable input is high, the associated driver gets enabled. As a result, the outputs become active and work in phase with their inputs. Similarly, when the enable input is low, that driver is disabled, and their outputs are off and in the high-impedance state.
Technical Specifications:
- It can be used to run Two DC motors with the same IC.
- Speed and Direction control is possible
- Motor voltage Vcc2 (Vs): 4.5V to 36V
- Maximum Peak motor current: 1.2A
- Maximum Continuous Motor Current: 600mA
- Supply Voltage to Vcc1(Vcc): 4.5V to 7V
- Transition time: 300ns (at 5Vand 24V)
- Automatic Thermal shutdown is available
- Available in 16-pin DIP, TSSOP, SOIC packages
Package Includes:
- 1 Piece- Dual Motor Driver L293D Module With 7505
Weight | 25 g |
---|---|
Dimensions | 40 × 32 × 15 mm |
Related products
-
PIR Motion Detector Sensor Module (Hc-Sr501 Pyroelectric Infrared)
₹120.00₹110.00Add to cartThe Passive Infrared Sensor (PIR) sensor module is used for motion detection. It can be used as a motion detector for security systems or robotics. It works on 5V DC and gives TTL output which can be directly given to microcontroller or to relay through a transistor. It consists of a pyroelectric sensor and Fresnel lens that …
PIR Motion Detector Sensor Module (Hc-Sr501 Pyroelectric Infrared)Read More
-
Tsop Proximity Sensor Module
₹180.00₹150.00Add to cartThe TSOP 1738 is a member of IR remote control receiver series. This IR sensor module consists of a PIN diode and a preamplifier which are embedded into a single package. The output of TSOP is active low and it gives +5V in off state. When IR waves, from a source, with a center frequency of 38 kHz incident on it, …
-
L9110S H Bridge Stepper Motor Dual DC Driver
₹140.00₹125.00Add to cartThe HG7881 (L9110) is a compact motor driver board that supports a voltage range from 2.5-12V at 800mA of continuous current. These chips have built-in output clamp diodes to protect your sensitive microcontroller electronics. They are suitable for small robot projects. Each L9110 chip is able to drive a single DC motor using two digital …
-
HC-05/HC-06 Wireless Bluetooth RF Transceiver Module
₹340.00₹325.00Add to cartHC-05/HC-06 Bluetooth Module with Breakout Board. This comes with a tiny push-button switch to enable programming. HC-05/HC-06 module Bluetooth SPP (Serial Port Protocol) module, designed for wireless serial connection setup. It has EDR (Enhanced Data Rate) of 3Mbps Modulation with a complete 2.4GHz radio transceiver and baseband. It uses the CSR Bluecore 04-External single-chip Bluetooth …
HC-05/HC-06 Wireless Bluetooth RF Transceiver ModuleRead More
Reviews
There are no reviews yet.