- Academic DIY Kits
- Academic Hobby Projects
- Academic Major Projects
- Academic Minor Projects
- Aeromodelling & Drone
- Development Boards
- Electronics- Active Parts
- Electronics- Passive Parts
- Electronics- Sensors
- Electronics– Accessories
- Mechanical Parts
- Motor, Actuator & Pump
- Robot Accessories
- Supply- Battery, Adopters
- Tools & Equipment
Top rated products
This is a multipurpose infrared sensor which can be used for obstacle sensing, line sensing, etc. and also as an encoder sensor. The sensor provides a digital output. The sensor outputs a logic one (+3.5V) at the digital output when an object is placed in front of the sensor and logic zero (0V) when there is no object in front of the sensor. An On-board RED LED is used to indicate the presence of an object.
This IR PROXIMITY/OBSTACLE SENSOR is designed to work with almost all ARDUINO boards and MICROCONTROLLERs – AVR, PIC, 8051, ARM etc. Operating Voltage: 5V
Adjustable Range using Preset (Potentiometer on board)
Since the sensor module works on INFRARED, for obstacles with reflective surfaces (white colored), the maximum range will be higher and for non-reflective surfaces (black colored), and the maximum range will be lower. This can, in turn, be used for detecting white/black lines (inline follower ROBOTs) or bright/dark objects (in object identification ROBOTs). Useful for various Robotic Applications, Room Visitor Counter Systems, etc.
Adjustable Range using Preset (Using Potentiometer Onboard)
- Operating Voltage: 5V DC
- Digital Output : Logic one (+3.5V DC) /Logic zero (0V DC)
- Mounting Hole of 2.5mm diameter for Easy Mounting.
- This can, in turn, be used for detecting white/black lines (inline follower ROBOTs)or bright/dark objects (in object identification ROBOTs)
- Useful for various Robotic Applications, Room Visitor Counter Systems, etc.
- COMPATIBLE WITH ARDUINO, RASPBERRY PI, ARM, AVR, PIC, 8051, etc.
- LED Status indicators to indicate the Obstacle (RED LED) status.
- 1 Piece- IR Sensor Module
|Dimensions||55 × 25 × 10 mm|
Imported, Indian, Hand Made
Flame Sensor/Infrared Receiver Module (Ignition Source Detection Module)
₹80.00Add to cart
This tiny Flame sensor infrared receiver module ignition source detection module is Arduino compatible can use to detect flame or wavelength of the light source within 760nm~1100nm also useful for Lighter flame detect at the distance 80cm. Greater the flame, farther the test distance. It has the Detect angle of 60 degrees and very sensitive to flame spectrum. It produces …
ADXL345 – Triple Axis Linear Accelerometer
₹125.00Add to cart
ADXL345 is a Breakout board for the Analog Device’s ADXL345 triple axis accelerometer. The module is populated with MOSFET based Voltage level conversion circuitry to enable you to interface different type of microcontrollers (3V3 & 5V). Apart from the above all, necessary components like decoupling capacitors ,filter capacitors ,pull up resistors and LED are also …
1 Channel 5Volt Relay Module
₹95.00Add to cart
This is a 5V, Single Channel Relay interface board; it’s useful to control various appliances, and other equipment’s with large current. It can be controlled directly by any Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, ARM, DSP, MSP430). Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or …
DS3231 Real Time Clock (RTC) Module
₹180.00Add to cart
DS3231 Module is a Bread Board friendly extremely precise I2C real time clock Module. This module made using DS3231 RTC and AT24C32 EEPROM integrated with temperature compensated crystal oscillator. It also has a built in comparator which monitors the status of VCC to detect power failures and to automatically switch to backup power supply. AT24C32 provides …