Category
- Academic DIY Kits
- Academic Hobby Projects
- Academic Major Projects
- Academic Minor Projects
- Aeromodelling & Drone
- Development Boards
- Electronics- Active Parts
- Electronics- Passive Parts
- Electronics- Sensors
- Electronics– Accessories
- Electronics–Modules
- Mechanical Parts
- Motor, Actuator & Pump
- Robot Accessories
- Supply- Battery, Adopters
- Tools & Equipment
Top rated products
-
L293D Multi Motor Driver Shield For Arduino SLAEX039
₹240.00₹225.00 -
SG90 9G Micro Servo Motor
₹130.00₹120.00 -
Wheel with Shaft Dia-6mm, Outer Dia-70mm, Face width-50mm
₹65.00₹60.00 -
LM358 IC Low Power Dual Operational Amplifier Op Amp IC
₹15.00₹9.00 -
Drilling Machine 3 Degree Of Working ₹9,500.00
L293D contains two inbuilt H-bridge driver circuits. In its common mode of operation, two DC motors can be driven simultaneously, both in forward and reverse direction. The motor operations of two motors can be controlled by input logic at pins 2 & 7 and 10 & 15. Input logic 00 or 11 will stop the corresponding motor. Logic 01 and 10 will rotate it in clockwise and anticlockwise directions, respectively.
Enable pins 1 and 9 (corresponding to the two motors) must be high for motors to start operating. When an enable input is high, the associated driver gets enabled. As a result, the outputs become active and work in phase with their inputs. Similarly, when the enable input is low, that driver is disabled, and their outputs are off and in the high-impedance state.
Technical Specifications:
- It can be used to run Two DC motors with the same IC.
- Speed and Direction control is possible
- Motor voltage Vcc2 (Vs): 4.5V to 36V
- Maximum Peak motor current: 1.2A
- Maximum Continuous Motor Current: 600mA
- Supply Voltage to Vcc1(Vcc): 4.5V to 7V
- Transition time: 300ns (at 5Vand 24V)
- Automatic Thermal shutdown is available
- Available in 16-pin DIP, TSSOP, SOIC packages
Note: Complete Technical Details can be found at the datasheet give at the end of this page.
Package Includes:
- 1 Piece- L293D Dual Motor Driver Module (Up to 1~2 Amp)
Weight | 25 g |
---|---|
Dimensions | 40 × 32 × 15 mm |
Related products
-
DS1307 Real Time Clock (RTC) Module
₹150.00₹140.00Add to cartThe DS1307 serial real-time clock (RTC) is a low-power, full binary-coded decimal (BCD) clock/calendar plus 56 bytes of NV SRAM. Address and data are transferred serially through an I²C, bidirectional bus. The clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with …
-
IR Sensor Module
₹50.00₹45.00Add to cartThis is a multipurpose infrared sensor which can be used for obstacle sensing, line sensing, etc. and also as an encoder sensor. The sensor provides a digital output. The sensor outputs a logic one (+3.5V) at the digital output when an object is placed in front of the sensor and logic zero (0V) when there is …
-
Rain Drop Sensor Module
₹95.00₹80.00Add to cartRain Sensor or detector is simple and easy to use the module for rain detector. The module works as a switch when rain falls on the module and also measures rain intensity. This rain module can measure beyond humidity detector, means it can measure what humidity cannot. The complete module comes with rain board, control …
-
ADXL335 – Triple Axis Linear Accelerometer
₹270.00₹260.00Add to cartADXL335 is a Breakout board based on 3 axis ADXL335 IC from Analog Devices. The Accelerometer Module require no external devices and works on 5V power supply. It can be directly interfaced to ADC of a microcontroller without any external components. This module can be used to sense motion or tilt(in case of non-moving) in …
Reviews
There are no reviews yet.