Category
- Academic DIY Kits
- Academic Hobby Projects
- Academic Major Projects
- Academic Minor Projects
- Aeromodelling & Drone
- Development Boards
- Electronics- Active Parts
- Electronics- Passive Parts
- Electronics- Sensors
- Electronics– Accessories
- Electronics–Modules
- Mechanical Parts
- Motor, Actuator & Pump
- Robot Accessories
- Supply- Battery, Adopters
- Tools & Equipment
Top rated products
-
BO Motor-100 RPM with Plastic Gear Side Shaft
₹90.00₹70.00 -
FT232RL / Uart 6 Pin TDI USB To TTL Serial Converter Adapter Module
₹210.00₹140.00 -
DC Geared Motor-3.5 RPM Center Shaft
₹190.00₹175.00 -
TCRT5000 Reflective Infrared Optical Sensor
₹45.00₹35.00 -
Four Wheel Steering System (4WS) ₹7,500.00
L293D is a dual H-bridge motor driver integrated circuit (IC). Motor drivers act as current amplifiers since they take a low-current control signal and provide a higher-current signal. This higher current signal is used to drive the motors. L293D contains two inbuilt H-bridge driver circuits. In its common mode of operation, two DC motors can be driven simultaneously, both in forward and reverse direction. The motor operations of two motors can be controlled by input logic at pins 2 & 7 and 10 & 15. Input logic 00 or 11 will stop the corresponding motor. Logic 01 and 10 will rotate it in clockwise and anticlockwise directions, respectively. Enable pins 1 and 9 (corresponding to the two motors) must be high for motors to start operating. When an enable input is high, the associated driver gets enabled. As a result, the outputs become active and work in phase with their inputs. Similarly, when the enable input is low, that driver is disabled, and their outputs are off and in the high-impedance state. They are designed to drive inductive loads such as relays, solenoids, dc and bipolar stepping motors, as well as their high-current/high-voltage loads in positive-supply applications.
Technical Specifications:
- Featuring Unit rode L293 and L293D
- Wide Supply-Voltage Range: 4.5 V to 36 V
- Separate Input-Logic Supply
- Internal ESD Protection
- Thermal Shutdown
- High-Noise-Immunity Inputs
- Functional Replacements for SGS L293 and
- SGS L293D
- Output Current 1 A Per Channel
- (600 mA for L293D)
- Peak Output Current 2 A Per Channel
- (1.2 A for L293D)
- Output Clamp Diodes for Inductive
- Transient Suppression (L293D)
Package Includes:
- 1 Piece-L293D Motor Driver IC Dual H-Bridge
Weight | 3 g |
---|
Related products
-
L298N Motor Driver Dual H-Bridge IC
₹190.00₹150.00Add to cartL298N is a high power version of L293D motor driver IC. It is a high voltage, high current, dual full-bridge driver designed to accept standard TTL logic levels (Control Logic) and drive inductive loads such as relays, solenoids, DC and Stepper motors. Two enable inputs are provided to Enable or disable the device independently of the input signals. The emitters …
-
NE555, NE555P – Timer IC
₹15.00₹12.00Add to cartThe NE555 has a trigger level of approximately one-third of the supply voltage and a threshold level equal approximately to two-thirds of the supply voltage. These levels can be altered by use of the control voltage terminal (CONT). The 555 can be used in countless applications and has three recognised operating modes. In mono stable …
-
ULN2803 IC – Darligton Transistor Array
₹32.00₹25.00Add to cartThe ULN2803A device is a DIP IC having high-voltage, high-current Darlington transistor array. The device consists of (Single Output) eight NPN Darlington pairs that feature high-voltage output with common cathode clamp diodes for switching inductive loads. Technical Specifications: 500-mA-Rated Collector Current. High-Voltage Outputs: 50 V. Output Clamp Diodes. Inputs Compatible With variable types of logic. Relay-Driver …
-
LM358 IC Low Power Dual Operational Amplifier Op Amp IC
₹15.00₹9.00Add to cartThis IC LM358 is 8-pin IC. These devices consist of two independent, high-gain frequency-compensated operational amplifiers designed to operate from a single supply or split supply over a wide range of voltages. Common-Mode Input Voltage Range Includes Ground, Allowing Direct Sensing Near Ground. Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage: 32 V (26 …
LM358 IC Low Power Dual Operational Amplifier Op Amp ICRead More
Reviews
There are no reviews yet.