Category
- Academic DIY Kits
- Academic Hobby Projects
- Academic Major Projects
- Academic Minor Projects
- Aeromodelling & Drone
- Development Boards
- Electronics- Active Parts
- Electronics- Passive Parts
- Electronics- Sensors
- Electronics– Accessories
- Electronics–Modules
- Mechanical Parts
- Motor, Actuator & Pump
- Robot Accessories
- Supply- Battery, Adopters
- Tools & Equipment
Top rated products
-
PAM8403 5V 2-Channel Stereo Audio Amplifier Module
₹75.00₹65.00 -
Microphone 9*7mm
₹25.00₹20.00 -
Diode-1N4007
₹0.80₹0.50 -
4.5K ohm Resistor (1/4W, +/- 5%)
₹1.00₹0.50 -
L293D Multi Motor Driver Shield For Arduino SLAEX039
₹240.00₹225.00
The great little solution’s for wireless control capable of up to 2mbit communication with a range from 40 to 100m. Has an onboard antenna. The nRF24L01 is a single-chip 2.4GHz transceiver with an embedded baseband protocol engine (Enhanced ShockBurst™), designed for ultra low power wireless applications.
The nRF24L01 is designed for operation in the worldwide ISM frequency band at 2.400 – 2.4835GHz. An MCU (microcontroller) and very few external passive components are needed to design a radio system with the nRF24L01. The nRF24L01 is configured and operated through a Serial Peripheral Interface (SPI.) Through this interface the register map is available. The register map contains all configuration registers in the nRF24L01 and is accessible in all operation modes of the chip.
The embedded baseband protocol engine (Enhanced ShockBurst™) is based on packet communication and supports various modes from manual operation to the advanced autonomous protocol operation. Internal FIFOs ensure a smooth data flow between the radio front end and the system’s MCU. Enhanced ShockBurst™ reduces system costs by handling all the high-speed link-layer operations. The radio front end uses GFSK modulation. It has user-configurable parameters like frequency channel, output power, and air data rate.
Technical Specifications:
- NRF24L01 is a universal ISM band monolithic transceiver chip works in the 2.4-2.5GHz
- Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
- The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
- As the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
- Built-in 2.4GHz antenna supports up to six channels of data reception
- Size: 15 x 29mm
- Low operating voltage: 1.9-3.6V
- 125 channels, multi-point communication, and frequency hopping to meet the communication needs
- High Rate: 2Mbps, as air transmission time is very short, greatly reducing collision phenomena in wireless transmission (air transfer rate of software setting: 1Mbps or 2Mbps)
- Low power consumption: When the answer mode communication, fast air transmission and start-up time, which greatly reduces the current consumption
- Low application cost: NRF24L01 integrated part of all high-speed signal processing related to RF protocol, such as automatic retransmission of lost packets and automatically generate response signals, etc.
- NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
- Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient
Package Includes:
- 1 Piece- NRF24L01 2.4GHz Wireless Transceiver Module
Weight | 25 g |
---|---|
Dimensions | 25 × 18 × 12 mm |
Related products
-
Tsop Proximity Sensor Module
₹180.00₹150.00Add to cartThe TSOP 1738 is a member of IR remote control receiver series. This IR sensor module consists of a PIN diode and a preamplifier which are embedded into a single package. The output of TSOP is active low and it gives +5V in off state. When IR waves, from a source, with a center frequency of 38 kHz incident on it, …
-
FT232RL / Uart 6 Pin TDI USB To TTL Serial Converter Adapter Module
₹210.00₹140.00Add to cartEasily convert USB to TTL serial using this FT232 module. Plug one end into your USB port and on the other you’ll have TTL Serial on the 6 pins. This module converts a USB port into a serial port, with TTL voltage levels compatible with most microcontroller cards such as Arduino / Pic / Raspberry …
FT232RL / Uart 6 Pin TDI USB To TTL Serial Converter Adapter ModuleRead More
-
Ultrasonic Sensor Module (Distance Measuring Module)
₹140.00₹130.00Add to cartThis ultrasonic sensor module can be used for measuring distance, object sensor, motion sensors etc. High sensitive module can be used with a microcontroller to integrate with motion circuits to make robotic projects and other distance, position & motion sensitive products. The module sends eight 40 KHz square wave pulses and automatically detects whether it …
Ultrasonic Sensor Module (Distance Measuring Module)Read More
-
DS1307 Real Time Clock (RTC) Module
₹150.00₹140.00Add to cartThe DS1307 serial real-time clock (RTC) is a low-power, full binary-coded decimal (BCD) clock/calendar plus 56 bytes of NV SRAM. Address and data are transferred serially through an I²C, bidirectional bus. The clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with …
Reviews
There are no reviews yet.