Training
Offers
Robot Chasis
Best Price
Google Review
SW-1801P Normally open vibration sensor module
Original price was: ₹ 188.00.₹ 139.00Current price is: ₹ 139.00.
Quick Review:
- Operating voltage: 3.3 to 5VDC
- Comparator: LM393
- Ball Rolling type of tilt sensor
- This small module is easy to use
- A fixed bolt hole for easy installation
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
3 in stock
3 in stock
32 in stock
The Tilt Sensor Vibration Alarm Vibration Switch Module for Arduino come with the basic components for operation. Supplying power and it is good to be used. Attach it to object and it will detect whether the object is tilt. Simple usage as it is the digital output, so you will know the object is tilt or not by reading the output. It uses SW-460D or SW-520D tilt sensor. The Tilt Sensor is the ball rolling type, NOT Mercury type. Comes with an M3 mounting hole for ease of attaching it to an object. On board, it provides a tilt switch, high sensitivity and commonly being used for tilt detection. The module comes with power LED and status LED for the visual indicator. The module will output logic LOW when the module is not tilted until the threshold angle; it will output logic HIGH when it is tilted over the threshold angle. We have tested, the tilt angle is quite big, from 45 degrees to 130 degrees. However, it depends on the angular velocity too. It can be used as a vibration sensor too.
Pin Description:
- VCC: Connect the power supply positive
- GND: Connect the power supply negative
- DO: Digital signal output
- AO: Use this vibration sensor to disable this function
Instructions:
- The product does not shake, the vibration switch was disconnected, the output high, Greenlight does not light
- The product vibration, the vibration switch instantaneous conduction, the output low, green light
- The output can be directly connected with the microcontroller, through the microcontroller to detect high and low levels, which to detect whether the environment vibration, play a warning role
Use:
For a variety of vibration trigger, reported Pao alarm, intelligent car, electronic building blocks and so on.
Please note that this module in the induction of a small shock when the trigger time will be very short, not enough to drive the relay, some people can directly connect with the relay module data, the actual use of poor results.
Technical Specifications:
- Operating voltage: 3.3 to 5VDC
- Comparator: LM393
- Ball Rolling type of tilt sensor
- This small module is easy to use
- A fixed bolt hole for easy installation
- Wide voltage LM393 comparator
Package Includes:
- 1 Piece–SW-1801P Normally open vibration sensor module
Shipping & Delivery
We try our best to reach each and every corner of India using a few of the best courier services running in the Country such as Delhivery, DTDC, BlueDart, XpressBees, Ecom Express, etc. as per the feedback for the courier partner at the customer’s location. A few of the interior parts of India which are not covered by these courier services are covered by India-Post by us. We apply our best effort on daily basis to dispatch the order the same day it is ordered or within the next 24 hours of the order placed. Most of the orders that are placed before 1 PM are dispatched and shipped the same day. The orders placed post that is scheduled for next day shipment. The same effort is applied throughout the week including weekdays and sometimes weekends and public holidays as well. We facilitate local pickup (self-pickup for the local customers) on the weekdays and partially on weekends also.
Ercoms Warranty
All electronic items are imported, therefore, they do not come with a warranty or guarantee. Rest assured, We meticulously inspect each product before dispatch. In the rare event of any defects, replacements will be provided after a thorough examination.
This item is covered with a standard warranty of 15 days from the time of delivery against manufacturing defects only. This warranty is given for the benefit of Ercoms customers from any kind of manufacturing defects. Â Reimbursement or replacement will be done against manufacturing defects only.
What voids warranty:
If the product is subject to misuse, tampering, static discharge, accident, water or fire damage, use of chemicals & soldered or altered in any way.
**Note: Shipping Charges Applied When Need Replacement or Refund.
Other Info
- Country of origin:Â China
- Brand/Manufacturer: Generic
- Packer/ Importer: Ercoms Robotics Lab
- No Warranty/Guarantee Of Chinese Goods.
Only logged in customers who have purchased this product may leave a review.
Related products
-
ULN2003 Stepper Motor Driver Module
Original price was: ₹ 125.00.₹ 59.00Current price is: ₹ 59.00.Add to cartQuick Review:
- Motor Driver Chip: ULN2003A
- Power supply: 5-12V
- Signal indicator: 4-way
- Step angle: 5.625 x 1 / 64
- Reduction ratio: 1 / 64
- Phase: 4
- Current / Phase: 5V
- Chip all the pins already leads for easy connection to use
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
-
Dual Monster Moto Shield VNH2SP30 DC Motor Driver 2x14A (Peak 30A)
Original price was: ₹ 1,850.00.₹ 1,648.00Current price is: ₹ 1,648.00.Read moreQuick Review:
- Voltage Range: 5.5V – 16V
- Maximum Current rating: 30A
- Practical Continuous Current: 14 A
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Current sense output proportional to motor current
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
-
5V Step-Up Power Module Lithium Battery Charging Protection Board USB (134N3P)
Original price was: ₹ 95.00.₹ 89.00Current price is: ₹ 89.00.Add to cartQuick Review:
- BAT Discharging Stop Voltage: 2.9V.
- Discharging Efficiency: 85%(input 3.7V output 5V/1A).
- Indication: Charging and discharging
- When charging: red light flashing.
- Fully charged: Red light glows for a long time.
- Integration charging management and discharging management.
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
-
RAMPS 1.4 3D Printer Controller Board Arduino Mega Shield
Original price was: ₹ 575.00.₹ 549.00Current price is: ₹ 549.00.Read moreQuick Review:
- Supply Voltage: 12V
- Standard interfaces (such as that of the extruder)
- Reserved GCI like I2C and RS232
- 3 MOSFET’s are applied to the heater/ fan and thermistor circuit.
- Another 5A was added to protect the parts.
- An 11A fuse is added to the hotbed.
- Support 5 stepper drive board
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
-
A4988 Stepper Motor Driver Module with Aluminium Heat Sink
Original price was: ₹ 128.00.₹ 89.00Current price is: ₹ 89.00.Add to cartQuick Review:
- simple step and direction control interface
- Short-to-ground and shorted-load protection
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
-
CNC Shield V3 3D Printer Expansion Board
Original price was: ₹ 249.00.₹ 165.00Current price is: ₹ 165.00.Add to cartQuick Review:
- Arduino CNC Shield Version 3
- GRBL 0.9 compatible.
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
- Coolant enable
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
-
Ultrasonic Sensor Module
Original price was: ₹ 110.00.₹ 84.00Current price is: ₹ 84.00.Add to cartQuick Review:
- IC Chip: LM393
- Operating Voltage: 3.3V to 5V
- Output: Digital and Analog
- Microphone Type: Electret condenser
- Sensitivity Adjustment: Potentiometer
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
-
L293D Multi Motor Driver Shield For Arduino-SLAEX039
Original price was: ₹ 230.00.₹ 149.00Current price is: ₹ 149.00.Add to cartQuick Review:
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
For all Bulk & B2B Product Enquiries
Kindly share your requirements at Contact Us.
Availability:Â
Reviews
There are no reviews yet.